FURNACE INSTALLATION
Commercial Furnace Installation in Southeast Michigan
The system you install today will run your facility for the next 15 to 20 years. Friedman Mechanical engineers and installs commercial heating systems that are sized right, built to code, and designed to perform for the long haul.
Installation is an engineering decision, not just a swap.
Replacing or installing a commercial furnace isn't a plug-and-play job. The wrong equipment size, improper venting, inadequate ductwork, or a poor controls integration can cost a facility in energy waste and repair calls for years after install day.
Friedman Mechanical approaches every installation as an engineering project. We start with a full load calculation, evaluate your building's specific demands, and spec the right equipment before a single component is ordered. Then our certified technicians execute the install cleanly, completely, and in compliance with all applicable codes.
No subcontractors. No shortcuts. No oversized or undersized equipment that creates problems down the road.
Commercial HVAC services
Building automation & controls integration
New heating equipment installed by Friedman Mechanical is fully integrated with your building automation system or controls infrastructure. Digital and pneumatic controls, zone sensors, and programmable thermostats are configured and commissioned as part of every installation.
Commercial Furnace Installation
Fast, accurate diagnosis and repair for commercial furnaces and boilers of all makes and configurations. We minimize downtime and get systems back online quickly, including 24/7 emergency response when it can't wait.
Rooftop Unit (RTU) Installation
Packaged rooftop unit installation for commercial properties, including full coordination of crane logistics, roof curb placement, duct tie-ins, electrical connections, and controls commissioning. We minimize facility disruption and leave the system fully tested and documented on completion.
System Replacement & Retrofit
Upgrading aging equipment? We assess the existing system, identify what can be retained and what needs to go, and execute the replacement with minimal downtime. Particular attention is paid to code compliance, efficiency improvements, and integration with modern controls.
Service Area
Friedman Mechanical provides commercial cooling services throughout Southeast Michigan, including:
- Farmington Hills
- Detroit
- Ann Arbor
- Troy
- Southfield
- Pontiac
- Dearborn
- Livonia
- Royal Oak
- Auburn Hills
- Sterling Heights
And surrounding Southeast Michigan communities.
Equipment We Service
Friedman Mechanical technicians are factory-trained and experienced across all major commercial HVAC equipment manufacturers.
Don't see your brand listed? Call us. If it runs, we can service it.
Commercial Heating
The System You Install Today Runs Your Facility for the Next 15–20 Years.
Commercial furnace installation across Southeast Michigan — engineered from a full load calculation, permitted, code compliant, and commissioned correctly. No subcontractors, no shortcuts.
-
Engineered & Properly Sized
Full load calculation based on your building's square footage, insulation, occupancy, and usage patterns before any equipment is specified — oversized and undersized systems both cause long-term performance and efficiency problems
-
Ductwork & Distribution Design
Custom sheet metal ductwork design and installation, airflow balancing across zones, and integration with existing distribution systems — static pressure and airflow balance verified, not estimated
-
Replacement, Retrofit & Code Compliance
Aging equipment replaced with minimal downtime — existing infrastructure assessed for reuse, full permitting managed, code compliant on completion, and new equipment integrated with your BAS or controls infrastructure
-
We perform a full load calculation based on your building's square footage, insulation values, occupancy, usage patterns, and local climate data. Oversized and undersized equipment both cause long-term performance and efficiency problems — proper sizing is non-negotiable.
-
Yes. Friedman Mechanical manages all required permits and ensures every installation meets local mechanical codes and manufacturer specifications. We document everything and provide sign-off at project completion.
-
Yes. Our technicians are experienced with digital and pneumatic controls and BAS integration across most major platforms. New equipment is fully commissioned and configured before we leave the site.
-
Yes. We offer customized preventive maintenance agreements for all equipment we install. Clients who enroll in a maintenance plan at installation benefit from priority scheduling and a team that already knows their system.
-
Timeline varies based on equipment type, facility complexity, and site conditions. We provide a project schedule as part of the estimate and work to minimize operational disruption throughout the install.